EVE Audio SC208 Product Manual
EVE Audio SC208 Product Manual
The EVE Audio SC208 is an 8-inch two-way active studio monitor from EVE Audio’s SilverCone SC series. This page provides key setup, operation, positioning, DSP filter, safety, warranty, and technical specification information from the EVE Audio SC207/SC208 product manual.
The SC208 is designed for professional studios, project studios, larger nearfield setups, and monitoring environments where deeper low-frequency extension and higher output are useful. It combines an 8-inch SilverCone woofer, EVE Audio’s AMT RS2 tweeter, high-resolution DSP control, and dedicated amplification for the woofer and tweeter.
Download the EVE Audio SC208 Product Manual PDF
Download the full EVE Audio SC207 and SC208 product manual for complete setup instructions, operation details, filter controls, speaker positioning, technical specifications, warranty notes, and safety information.
EVE Audio SC208 Manual Overview
The EVE Audio SC208 product manual includes safety instructions, quick start setup, speaker connection guidance, front-panel operation, volume control, standby mode, mute mode, DSP filter settings, rear-panel DIP switches, mains voltage selection, speaker positioning, room acoustics, technical specifications, declaration of conformity, and warranty information.
SC208 Quick Start Setup
Before using the SC208, confirm that the package includes the loudspeaker, user manual, power cord, protective tweeter grid, and rubber feet. Check the mains voltage selector before powering on the monitor, and verify that the rear-panel DIP switches are set as intended.
Connect the SC208 to a playback source such as an audio interface, monitor controller, mixer, or DAC. The manual recommends starting with the output level of the source device as low as possible, then increasing gradually.
SC208 Inputs and Connections
The EVE Audio SC208 includes both balanced and unbalanced analog inputs. The balanced XLR input is preferred for most professional studio setups, while the RCA input can be used with unbalanced equipment.
- Balanced input: XLR
- Unbalanced input: RCA
- XLR pin assignment: Pin 1 shield, pin 2 hot, pin 3 cold
- RCA assignment: Center conductor signal, ring shield
- Maximum input level: 8 dBu
The manual notes that both analog inputs can be used at the same time, with the signals summed internally. If the input is overloaded, the front LED ring will blink.
SC208 Volume Control and Operation
The SC208 uses a front-panel control knob with an LED ring. This control manages volume adjustment, mute, standby mode, and access to the settings menu. The LED ring displays volume and setting changes depending on the selected LED display mode.
The volume control response is not linear. The adjustment steps become finer as volume increases, allowing more precise control near typical studio listening levels.
Standby Mode
Pressing and holding the front control for three seconds places the monitor in Standby Mode. In standby, the manual states that power consumption is reduced to less than 1 watt.
Mute Mode
To mute the SC208, turn the volume control counterclockwise until the minimum level is reached. The left LED indicates mute status.
SC208 DSP Filter Settings
The SC208 includes Low, High, and Desk filters designed to help adapt the monitor to room acoustics, placement, listening distance, and desk or mixer reflections. These filters are useful for fine-tuning, but they should not be treated as a substitute for proper monitor placement and acoustic treatment.
Low Filter
The Low-Shelf Filter adjusts frequencies below 300 Hz in 0.5 dB steps. This can help reduce excessive low-frequency buildup caused by walls, corners, room modes, or close placement.
High Filter
The High-Shelf Filter adjusts frequencies above 3 kHz in 0.5 dB steps. This can help compensate for reflective rooms, dead rooms, short listening distances, or longer listening distances.
Desk Filter
The Desk Filter is intended to reduce low-mid buildup from desks, mixers, meter bridges, and other hard reflective surfaces. On the SC208, the Desk Filter cut is centered at 160 Hz. When boosted, the Desk Filter operates around 80 Hz to add lower-frequency punch.
- Low filter: Below 300 Hz
- High filter: Above 3 kHz
- SC208 desk filter cut: 160 Hz
- Desk filter boost: 80 Hz
- Filter step size: 0.5 dB
- Maximum boost: +3 dB
- Maximum attenuation: -5 dB
SC208 Speaker Positioning
For best results, place the SC208 monitors symmetrically in relation to the listening position, side walls, rear wall, ceiling, and floor. The manual recommends keeping at least 0.5 m / 19 inches of distance from walls to reduce low-frequency buildup.
The SC208 is designed primarily for vertical placement. If the monitor must be placed horizontally, both monitors should remain symmetrical, with both tweeters pointing either inward or outward.
Recommended SC208 Listening Distance
The recommended listening distance for the EVE Audio SC208 is 1.5–2.5 m / 4.9–8.2 ft. The tweeter should ideally be positioned at ear height. If that is not possible, tilt the monitor so the tweeter is aimed toward the listener’s ears.
Stereo Setup
For stereo monitoring, the two monitors and the listening position should form an equilateral triangle. Aim both monitors toward the listening position, with each angle of the stereo triangle approximately 60 degrees.
SC208 Technical Specifications
| Monitor Type | 2-way active studio monitor |
| Woofer | 200 mm / 8 in |
| Tweeter | AMT RS2 |
| Frequency Range | 36 Hz – 21 kHz |
| Crossover Frequency | 2,800 Hz |
| Maximum SPL @ 1 m | 112 dB |
| Number of Amplifiers | 2 |
| Total Short-Term Output Power | 200 W |
| Woofer Amplifier | 150 W |
| Tweeter Amplifier | 50 W |
| Dimensions W x H x D | 255 x 390 x 330 mm / 10.04 x 15.35 x 12.99 in |
| Recommended Listening Distance | 1.5–2.5 m / 4.9–8.2 ft |
| Weight | 10.9 kg / 24 lb |
SC208 Safety Notes
The EVE Audio manual advises users not to open the unit, not to bypass the fuse, and not to attempt internal service. The monitor should be connected to a grounded power outlet. Liquids, extreme temperatures, blocked airflow, and excessive sound pressure levels should be avoided.
SC208 Warranty Notes
The manual states that the manufacturer warranty is valid for two years from the date of purchase. Warranty coverage may be voided by incorrect installation, misuse, negligence, modification, unauthorized repair, or damage caused by events outside EVE Audio’s reasonable control.
EVE Audio Monitor Availability
Interested in EVE Audio studio monitors? Contact Pro Audio Clinic for current availability, pricing, and comparable studio monitor options.
Need the 7-inch version? View the EVE Audio SC207 Product Manual.
Frequently Asked Questions
What is the EVE Audio SC208?
The EVE Audio SC208 is an 8-inch two-way active studio monitor with an AMT RS2 tweeter, DSP-based controls, and dedicated amplification for the woofer and tweeter.
What is the recommended listening distance for the SC208?
The manual lists the recommended listening distance for the SC208 as 1.5–2.5 m, or approximately 4.9–8.2 ft.
Does the SC208 have balanced inputs?
Yes. The SC208 includes a balanced XLR input and an unbalanced RCA input.
How is the SC208 different from the SC207?
The SC208 has an 8-inch woofer, deeper listed low-frequency extension, higher maximum SPL, greater total short-term output power, larger dimensions, and higher weight than the SC207.
Can the SC208 be placed horizontally?
The SC208 is designed mainly for vertical placement. If horizontal placement is required, both monitors should remain symmetrical, with tweeters pointing either inward or outward.
What PDF manual covers the SC208?
The EVE Audio SC207 and SC208 share the same product manual PDF, which includes setup, operation, positioning, technical specifications, safety, and warranty information.
This page is provided as an informational resource for EVE Audio SC208 users. Product specifications, warranty terms, and setup requirements should be verified with the official manufacturer documentation before purchase, installation, or service.